Window contact switch

DescriptionWindow contact switch radio system, white, with external aerialThe COMPAIR® window contact switch radio system is a clever complete solution for targeted management of exhaust air control. It is used if, in addition to the extractor bonnet, there are also room air-dependent fireplaces such as a stove or fireplace. The installation of the wireless exhaust air control or a wired control is required by law under the conditions mentioned. Negative pressure in the room is avoided, which can lead to the formation of dangerous gases without a fresh air supply from outside. The set includes a safety switch, which is used to connect the cooker bonnet to the mains supply. There are also two contact switches with wireless radio transmission, which are attached to the window frame and the window sash. If one of the fireplaces is in operation, the extractor bonnet can only be switched on if the window is recognised as open. The contact switch is equipped with an external aerial to ensure reliable transmission of information. This applies, for example, when using a stainless steel chimney cowl, as this attenuates the signal. The aerial is attached to the wall or ceiling next to the panelling.Safety switches with wirelessradio transmission via an external antenna for use in difficult reception conditions, e.g. when installed behind stainless steel panelling. Ready to plug in with transmitter and receiver, incl. installation material and batteries (long service life, low energy consumption).- Switching capacity up to 1150 W (5 A) Manufacturer information according to general product safety (GPSR)Naber GmbHEnschedestr. 2448529 NordhornGermanyPhone: +49 5921 704-0E-mail: naber@naber.com

DescriptionWindow contact switch for hob ventilators, white, with external antennaThe COMPAIR® window contact switch for trough ventilators only allows the exhaust air system to be used when the window is tilted or fully open. To determine this status, the two-part contact switch is attached to the window frame and the window sash. The built-in receiver integrated via the fan motor supply line receives the relevant information wirelessly by radio signal. As the electrical system of the hob ventilator or extractor bonnet is interfered with, the warranty conditions of the respective manufacturer should be taken into account before use. An external aerial can be used to overcome difficult reception conditions in the kitchen, for example when installed under a stainless steel cover. The complete package includes the batteries required for operation, including battery monitoring. More safety is provided by the integrated radio range monitoring. In the case of a hob fan with BLDC motor, the radio exhaust air control can be integrated separately via the third phase, as the required connection is often already available.Safety switches with wirelessradio transmission via an external aerial for use in difficult reception conditions, e.g. when installed behind stainless steel panelling or a furniture body. Installation in the extractor system is carried out via the connection to the fan motor supply line (motor supply line)ATTENTION: The electrical system of the extractor system must be accessed for this!Observe the guarantee/warranty conditions of the bonnet manufacturer.Complete system with transmitter and receiver, incl. installation material and batteries (long service life, low energy consumption).- Switching capacity up to 1150 W (5 A)- Radio link monitoring- Battery monitoring- Relay contact 5 A NO contact (potential-free)- Installation in extractor bonnet (motor supply line)- Tested in accordance with EU Directives 2014/53/EU (RED), 2014/35/EU and 2014/30/EU- When installed in a conventional extractor bonnet, the lighting can also be switched on when the fan motor is switched off.Note on use in combination with BLDC motors:Some extractor bonnets, hob ventilators and ventilation systems have a so-called BLDC motor. This can be switched separately when using the third phase (phases one and two are used for the hob). A corresponding connection is often already provided by the appliance industry - and can be used for the wireless radio switch. We recommend 7051001 for the classic single-phase AC motor. Please observe the installation instructions at www.naber.com! Manufacturer information according to general product safety regulations (GPSR)Naber GmbHEnschedestr. 2448529 NordhornGermanyPhone: +49 5921 704-0E-mail: naber@naber.com

Description Window contact switchWindow contact switch cable system, window contact switch, whiteThe COMPAIR® window contact switch cable system enables efficient exhaust air control in the event that there is an open fireplace in the room in addition to the extractor bonnet. This includes stoves and fireplaces, for example. The two-part magnetic contact switch is attached directly to the window frame and to the window sash to detect whether the window is open or closed. The connection to the safety switch is made via a sensor cable, which is 6 metres long, leaving plenty of scope for installation. This connection means that the extractor bonnet can only be operated when the window is open. This prevents exhaust fumes from active fireplaces from entering the room. Other important features of the cable exhaust air control include an integrated cable breakage monitor and the safety switch in the form of a safety bracket that is firmly screwed to the switch.Safety switch with cable break monitoring and plug-in safety device. Ready to plug in with 6 m sensor cable, incl. installation material. No batteries required.- Switching capacity up to 1400 W (6 A) Manufacturer information according to general product safety (GPSR)Naber GmbHEnschedestr. 2448529 NordhornGermanyPhone: +49 5921 704-0E-mail: naber@naber.com